C08
electric forklift
C series brake is a spring-pressurized electromagnetic power-off brake, which is mainly used for braking the driving wheels of small and medium-sized electric forklifts. It is installed in the driving wheel assembly to brake the shaft of the driving wheel, so as to achieve the electric Forklift parking and emergency braking make users more labor-saving, safer and more efficient!
Key Features
● For deceleration and braking
● Low noise brake sound is small
●Large angle design; Large angle steering design, more flexible operation
● Small volume to achieve large torque
● Torque range 6-16(N. m)
● Long service life
● Use imported high wear-resistant friction plate, durable
● Meet the use of high temperature environment
● Brake operating environment temperature -10 ~ +40(℃)
● Closed design, improve the protection level
Performance Parameters
Dimensions and Schematic Diagram
| Seat Number | A | B | L | V | K | a | T | H | d |
| 6 | 84 | 72 | 18 | 3-4M | 36.45 | 0.25 | 5 | 17.3 | 15 |
| 8 | 102 | 90 | 20 | 3-5M | 43.75 | 0.25 | 5 | 16.3 | 14 |
| 10 | 130 | 112 | 20 | 3-6M | 50.35 | 0.3 | 6 | 22.8 | 20 |
| 12 | 150 | 132 | 25 | 3-6M | 56.4 | 0.3 | 6 | 22.8 | 20 |
| 14 | 165 | 145 | 30 | 3-6M | 69.5 | 0.35 | 8 | 28.3 | 25 |
| (Note: Please refer to the drawings of specific specifications for detailed dimensions) | |||||||||
use precautions
1. The brake is mostly made of soft materials. Avoid knocking, dropping or using too much force during installation, otherwise it may cause scratches or deformation of the brake and affect the use. Please pay attention during installation.
2. Please note that the lead wire of the brake is not stretched by force, and the lead wire is bent too much or picked up by hand, which may damage the lead wire and cause the brake to fail to work.
3. Our brakes are dry double-sided friction plate brakes. If the friction surface is stained with oil or water, it will cause the torque of the brake to drop, so it needs to be used in a dry state. In order to prevent oil or water and dust, please use a protective cover.
4. Excessive voltage fluctuations will affect the performance of the brake, so the use of the brake voltage control in the range of ± 10% of the rated voltage, and smooth no interference.
5. The working clearance of the brake has been adjusted when leaving the factory, so there is no need to adjust it when in use, and please do not open the brake without permission. If the gap is not appropriate, the brake may not work properly.
6. Special attention: when the motor rotates, the brake must be opened, and forced drag with brake is not allowed! Drag with brake will damage the brake in a short time!
7. The installation screws are required to be fixed with special glue for thread. When applying glue to the screws, please be careful not to apply it to the surface of the rotor and the surface of the square wheel.
8. The installation accuracy of the brake is not good, which may cause the brake to make noise during operation. Please pay attention to control. The allowable values are shown in the following table:
| allowable value | Seat Number | ||||
| 6 | 8 | 10 | 12 | 14 | |
| T | 0.2 | 0.2 | 0.3 | 0.3 | 0.3 |
| Z | 0.03 | 0.04 | 0.05 | 0.05 | 0.06 |
